|
发表于 2021-9-1 21:54:32
|
显示全部楼层
Industry process standardsThe industry process standards include all standards used to design and manufacture FRP and Dual Laminate products.ASME RTP-1 – Reinforced thermoset plastic corrosion resistant equipment. ASME RTP-1, section M-14 for Dual Laminate products DVS 2205 Calculation of thermoplastic tanks and apparatus DVS 2207-3 Hot gas welding of thermoplastic polymers; panels and pipes DVS 2207-1, 2, 11, 15 Heated tool welding of pipes DVS 2207-4 Welding of thermoplastics; Extrusion welding for panels and pipes ASTM D3299 Standard specification for glass fiber reinforced thermoset resin chemical resistant tanks ASTM D4163 Standard specification for Reinforced thermosetting resin pressure pipe ASTM D2996 Standard specification for filament wound reinforced thermosetting pipe ASTM D2310 Classification system for reinforced thermosetting resin pipe ASTM D4097 Standard specification for contact molded glass fiber reinforced thermoset resin chemical resistant tanks DIN 16867 – Glass fiber reinforced polyester resin pipes, fittings and joints DIN 16965, part 1 to 5 – Wound glass fiber reinforced polyester resin pipes DIN 16966, part 1 to 6 – Glass fiber reinforced polyester resin pipes and joints Material specification standardsThis section includes all standards use for determining physical properties of thermoset and thermoplastic resins.ASTM D638 Test method for tensile properties of plastics ASTM D695 Test method for compressive properties of rigid plastics ASTM D790 Test method for flexural properties of reinforced and non-reinforced plastics ASTM D648 Test method for deflection temperature of plastic under flexural load ASTM D256 Test method for impact resistance of plastic materials ASTM D2583 Test method for indention of hardness of rigid plastics by means of barcol impressor ASTM D2584 Test method for ignition loss of cured reinforced resins ASTM E84 Test method for surface burning characteristics of building materials ASTM D696 Test method for coefficient of linear thermal expansion of plastics Thermoplastic components classification PVC & CPVC : ASTM-D1784 PP : ASTM-D4101 PE : ASTM-D1248 PVDF : ASTM-D3222 ECTFE : ASTM-D3275 ETFE : ASTM-D3159 MFA : ASTM-D6314 FEP : ASTM-D3368 PFA : ASTM-D3307 Quality process standardsASTM D2563, level 1 to 4 ASME RTP-1, level 1 & 2 CAN/CGSB-41.22-93 CIL 4200 & 4201 ASTM C1147 - Short term tensile weld strength of chemical resistant thermoplastics DVS 2201-1 Imperfection in thermoplastic welding joints Examination of plastic welders Extrusion welding 工业过程标准 工业过程标准包括所有用于设计和制造FRP和复合产品的标准。 ASME RTP-1 –热固性塑料增强防腐设备。 ASME RTP-1, 第M-14节适用于复合产品。 DVS 2205 热塑性塑料增强储罐和设备的计算。 DVS 2207-3 热塑性塑料板材和管材的热风焊接。 DVS 2207-1, 2, 11, 15 管道的机焊。 DVS 2207-4 热塑性塑料的焊接;板材和管材的模压焊接。 ASTM D3299 热固性树脂耐化学性玻璃钢储罐的标准。 ASTM D4163热固性树脂耐压玻璃钢管道的标准。 ASTM D2996热固性树脂缠绕玻璃钢管道的标准。 ASTM D2310热固性树脂玻璃钢管道系统分类。 ASTM D4097耐化学性热固性树脂玻璃钢模压储罐的标准。 DIN 16867 – 聚乙烯树脂玻璃钢管道,接头和连接件。 DIN 16965, 第1到 5节 –聚乙烯树脂玻璃钢管道的缠绕。 DIN 16966, 第1到 6节–聚乙烯树脂玻璃钢管道和连接件。 材料规范标准 以下规范标准包括所有用于决定热固性和热塑性塑料树脂物理性质的标准。ASTM D638 塑料拉伸强度的测试方法。 ASTM D695 脆性塑料的耐压性测试方法。 ASTM D790 增强塑料及非增强塑料的柔软性测试方法。 ASTM D648 塑料带荷的形变温度测试方法。 ASTM D256 塑料的抗冲击性测试方法。 ASTM D2583 用巴氏硬度计测试脆性塑料硬度的方法。 ASTM D2584 增强树脂燃烧的重量损失测试方法。 ASTM E84 建筑材料表面抗燃性测试方法。 ASTM D696 塑料衬里的热膨胀系数的测试方法。 热塑性材料的测试标准分类聚氯乙烯 & 氯化聚氯乙烯: ASTM-D1784 聚丙烯: ASTM-D4101 聚乙烯: ASTM-D1248 聚四氟乙烯: ASTM-D3222 ECTFE : ASTM-D3275 ETFE : ASTM-D3159 MFA : ASTM-D6314 FEP : ASTM-D3368 PFA : ASTM-D3307 质量过程标准 ASTM D2563, 第1 至 4 级 ASME RTP-1, 第1 至 2 级 CAN/CGSB-41.22-93 CIL 4200 & 4201 ASTM C1147 – 耐化学性热塑性树脂焊接拉伸强度的术语缩写。 DVS 2201-1 热塑性树脂接头焊接的失效。 挤压焊接焊机的测试。 1.钢材试验★ GB1954-1980 镍铬奥氏体不锈钢铁素体含量测定方法★ GB6803-1986 铁素体钢的无塑性转变温度 落锤试验方法 ★ GB2791-1982 碳素钢和低合金钢断口试验方法2.焊接性试验★ GB4675.1-1984 焊接性试验 斜Y型坡口焊接裂纹试验方法★ GB4675.2-1984 焊接性试验 搭接接头( CTS )焊接裂纹试验方法★ GB4675.3-1984 焊接性试验 T型接头焊接裂纹试验方法★ GB4675.4-1984 焊接性试验 压板对接(FISCO ) 焊接裂纹试验方法 ★ GB4675.5-1984 焊接热影响区最高硬度试验方法★ GB9447-1988 焊接接头疲劳裂纹扩展速率试验方法★ GB2358-1980 裂纹张开位移(COD)试验方法★ GB7032-1986 T 型角焊接头弯曲试验方法★ GB9446-1988 焊接用插销冷裂纹试验方法★ GB4909.12-1985 裸电线试验方法 镀层可焊性试验焊球法★ GB2424.17-1982 电工电子产品基本环境试验规程 锡焊导则 ★ GB4074.26-1983 漆包线试验方法 焊锡试验★ JB/ZQ3690 钢板可焊性试验方法★ SJ1798-1981 印制板可焊性测试方法3.力学性能试验方法★ GB2649-1989 焊接接头力学性能试验取样方法★ GB2650-1989 焊接接头冲击试验方法★ GB2651-1989 焊接接头拉伸试验方法★ GB2652-1989 焊缝及熔敷金属拉伸试验方法★ GB2653-1989 焊接接头弯曲及压扁试验方法★ GB2654-1989 焊接接头及堆焊金属硬度试验方法★ GB2655-1989 焊接接头应变时效敏感性试验方法★ GB2656-1981 焊接接头和焊缝金属的疲劳试验方法★ GB11363-1989 釺焊接头强度试验方法★ GB8619-1989 釺缝强度试验方法 4. 焊机材料试验 ★ GB3731-1983 涂料焊条效率、金属回收率和熔敷系数的测定★ GB3965-1983 电焊条熔敷金属中扩散氢测定方法★ GB8454-1987 焊条用还原钛铁矿粉中亚铁量的测定★ GB5292.1-1985 熔炼焊剂化学分析方法 重量法测定二氧化硅量★ GB5292.2-1985 熔炼焊剂化学分析方法 电位滴定法测定氧化锰量 ★ GB292.3-1985 熔炼焊再给大家提供点儿信息,希望大家光临我的精华帖子,多多支持:http://www.shenhui-weld.com/read.php?tid-2710-keyword-.htmlhttp://www.shenhui-weld.com/read.php?tid-2710.htmlhttp://www.shenhui-weld.com/read.php?tid-2711.htmlhttp://www.shenhui-weld.com/read.php?tid=2712&page=1&toread=1http://www.shenhui-weld.com/read.php?tid-2723-keyword-.html
|
|